home | contact | sitemap

Drilling Grinding Machines - Single Station

TL Series – Compact Turning Centers

Single Station

E-Catalogue

Click here to view e-catalogue

Models

078201300 SA-1300-110V
078221300 SA-1300-220V
078242500 SA-2500-110V
078262500 SA-2500-220V
078272000 SA-2000-110V
078282000 SA-2000-220V

Standard Accessories

1.SA-1300: ER-20 Ø3, Ø4, Ø5, Ø6, Ø7, Ø8, Ø9, Ø10, Ø11, Ø12, Ø13 x 11 pcs
SA-2000: ER-25 Ø3, Ø4, Ø5, Ø6, Ø7, Ø8, Ø9, Ø10, Ø11, Ø12, Ø13, Ø14,Ø15,Ø16,Ø17, Ø18, Ø19, Ø20, 18 pcs
SA-2500: ER-40 Ø13, Ø14, Ø15, Ø16, Ø17, Ø18, Ø19, Ø20,Ø21, Ø22, Ø23, Ø24, Ø25, Ø26, x 14 pcs
2.WHEEL (CBN For HSS): CBN #200 x 1pc (SA-1300, SA-2000) CBN #140 x 1 pc (SA-2500) (For high speed drill)
4mm Hex. Wrench x 1 pc

Optional Accessories

SA-1300: ER-20 Ø3.5, Ø4.5, Ø5.5, Ø6.5, Ø7.5, Ø8.5, Ø9.5, Ø10.5, Ø11.5, Ø12.5 x 10 pcs
SA-2000: ER-25 Ø3.5, Ø4.5, Ø5.5, Ø6.5, Ø7.5, Ø8.5, Ø9.5, Ø10.5, Ø11.5, Ø12.5, Ø13.5, Ø14.5, Ø15.5, Ø16.5, Ø17.5, Ø18.5, Ø19.5 x 17 pcs
SA-2500: ER-40 Ø13.5, Ø14.5, Ø15.5, Ø16.5, Ø17.5, Ø18.5, Ø19.5, Ø20.5, Ø21.5, Ø22.5, Ø23.5, Ø24.5, Ø25.5 x 13 pcs (Ø27, Ø28, Ø29, Ø30)
WHEEL (Diamond For Carbide):
- Diamond Wheel #400 x 1pc (SA-1300, SA-2000)
- Diamond Wheel #300 x 1pc (SA-2500)
  (For carbide dril

Features

Easy operation, precision grinding and cost saving.
Hand held for easy movement and can operate inside and outside of the room.
Use Diamond for long lasting service life and precise grinding angel.
Bult-in collet bracket for easy management collets

Operation

A. How to prepare for drill grinding:
- Make sure of the drill diameter to Choose the right Collet 24.
- Lock Collet into Collet Holder 17 properly.
- Insert drill into collet with 35 mm extension, no tight locking.
- Insert Collet Nut 16 into Collet 24 to lock Collet Holder
  17. Operate slightly to turn the drill by hand.
- Drill grinding preparation ends for Collet Chuck Set 60.
B. How to position the length and movement of the drill:
- Adjust Scale 15 in line with the dia. of drill.
- Put the whole set into Length Pre-Setting Bracket 11
  (According to Step A1 - A4) and insert Pin 41 into the slot.
- Turn Collet Chuck Set 60 clockwise to support against pin
  41 and turn drill clockwise until it touches drill cutting edge.
- Tight Collet Holder 17 clockwise.
- Take out of Collet Chuck Set 60 and make sure the cutting edge and collet holder slots are paralleled with each other. if not, the whole precess must be repeated. Attention: if drill spiral is different, please reset the parallel and adjust Scale Ring 15 in line With diameter of drill.
C. How to grind point angle:
- Put Collet Chuck Set 60 into Point Angle Bracket 4 and then insert the slot into
  the pin 41.
- Push Collet Chuck Set 60 to light touch the Wheel and turn clockwise and reverse
  about 5-6 times until grinding noise disappears.
- Take out Collet Chuck Set 60 and turn it 180 degree.
  Repeat Step 1 and 2 to finish point angle grinding.
D. How to grind drill chisel edge angle:
- Put Collet Chuck Set 60 into Point Angle Bracket 4 and then insert the slot into the
  pin 41.
- Push Collet Chuck Set 60 to light touch the wheel and turn clockwise and reverse
  5-6 times until grinding noise disappears.
- Take out Collet Chuck Set 60 and turn it 180 degree.
  Repeat Step 1 and 2 to finish grinding drill chisel edge angle on two drill chisel edge.
E. How to change grinding wheel:
- Loose Knot 23 and open Cover 20.
- Loose Screw 36 with 4mm hexagonal wrench.
- Change the grinding wheel and install it back.
- Make sure Cover 20 is tightened with Knob 23. Attention : If Screw 36 is not
  tightened properly, the Cover 20 will not be fastened enough. It is dangerous
  to switch on the machine before the Knob 23 being tightened fully.

Designed & Maintained by VInCom